1996 Saturn-Starting Problem

I have a 1996 Saturn SL1 and suddenly it won't start. It is low on gas so, my first thought was that with the severe cold yesterday had caused gasline freeze. The odd thing though, is that it isn't turning over. I put some gas line antifreeze in it and let it sit. It hasn't started yet but, I haven't tried it yet today. It has a new battery etc. Everything works. he radio, the blower, the lights all have plenty of power so, any ideas as to why it isn't attempting to turn over?





Thank you for any suggestions you may have!

 

Response:

http://www.freeautomechanic.com/nostart.html it seems to be an electrical problem. Before you do anything else make sure the blinkers work at normal pace, sometimes lights and all other electrical equipment work with a low battery, not the blinkers. Also, if the battery is not delivering sufficient power to crank the engine you should hear a ‘clicking’ noise, which is a sure sign of insufficient crank power and the battery needs to be charged and the posts cleaned and make sure they are tight.



Often, when the battery is new and fully charged the battery posts are no tight enough, or have enough corrosion –which is not always visible- to prevent from sending sufficient power to the starter. If this is the case, simply cleaning and retightening of the posts is enough to solve the problem.



If you have plenty of power and none of the above symptoms are present, the most likely alternative is a possible loose connection in the starter system.

controls on the steering wheel are not working

QUESTION:

2003 Honda pilot the controls on the steering wheel are not working. the horn the cruise control buttons and the volume buttons for the radio. they all stopped working at the same time. all the fuses are good. is there are any common problems with these SUV or what could it be?

ANSWER:

If all the fuse are good in all the fuse panels, under dash & under hood. Do you have brake lights? The only thing that shares in common it the cable reel. This helps make electrical contact for the items on the steering wheel to the steering column. Look for part#1 in the above diagram.

2001 Chrysler Intrepid battery light on

I went to a mechanic a month ago and replace the alternator because my battery light came on.  After about one month, the battery light came on again.  I went to the same mechanic and he said that the oxygen senor is faulty.  If I unplugged one oxygen sensor and I did not fix that one oxygen sensor. Will the car still run and won’t shut down?  What are the problems that the car might cause?



Response:



the battery light coming on has nothing to do with an oxygen sensor. I would suggest going to a different shop and having it retested.

An Oxygen sensor has nothing to do with the battery light. If you unplug an oxygen sensor it will still run but have bad gas mileage and the check engine light will come on.

PR: wait...  I: wait...  L: wait...  LD: wait...  I: wait... wait...  Rank: wait...  Traffic: wait...  Price: wait...  CY: wait...  I: wait...  YCat: wait...  I: wait...  Top: wait...  I: wait...  L: wait...  C: wait...

When I turn the headlights on the right turn signal blinks fast

When the headlights are off the turn signals work. When I turn the headlights on the right turn signal blinks fast. What is going on?

Answer:

Someone at one time has replaced one of the bulbs with the wrong one... It may look the same , but isn't the same..( ex. a 3057 was used instead of a 3157) . Again they look the same but are not the same. And yes I have seen this before.... Look closely at the bulbs and refer to the owners manual to make certain you install the correct ones. generally in the rear with the dual element bulbs.

Air Conditioner Problems

Any automotive air conditioning system employs four basic parts-a mechanical compressor, driven by the vehicle's engine; an expansion valve, which is a restriction the compressor pumps against; and two heat exchangers, the evaporator and the condenser. In addition, there is the refrigerant that flows through this system. Avoid the need for an auto air conditioner service call Look Below for car auto air conditioning repair Troubleshooting Procedures

The freon is compressed and flows through the condenser where it is cooled into a liquid. The freon passes through the receiver/dryer to remove moisture. Once the freon leaves and enters the expansion valve/orifice tube The high pressure liquid becomes a vapor and is extremely cold as it passes through the evaporator and on to the compressor to repeat the cycle.

Air Conditioner blows warm air
1. Air conditioner system is discharged. Have the system evacuated, charged and leak tested by an MVAC certified technician, utilizing approved recovery/recycling equipment. Repair as necessary.
2. Air conditioner compressor clutch not engaging. Check compressor clutch wiring, electrical connections and compressor clutch, and repair or replace as necessary.

ignition help

can any one give me instructions on how to take out and put a new ignition in my 96 lincoln town car not chiped



Response:

The Ignition Switch (electrical) is located on the top of the steering column assy. So if you unbolt the column it will drop down enough to replace the switch. The Lock Cyclender Assy is different. Remove the Steering Wheel Lock Nut. Mark the Wheel and Shaft for alignment on reassembly. With a Steering Wheel Puller remove the Steering Wheel. Remove the Horn assy. Remove the Steering Wheel Lock Plate by depressing to remove the retaing clip. Remove the Turn Signal Switch assy and reveal 1 screw that holds the Lock Cylender in place. Reverse for assembly.

Now no brake and parking lights

Simple job turned into something major, I hope not. 97 corolla, r. rear brake light not working. Replaced the bulb, everything was working good, decided to replace all bulbs, Antie told me she doesn't remember when they were changed. placed all new bulbs, 1157 for brake lights, 1156 for backup lights. Now no brake and parking lights. Signal and hazard lights are working, I wanted to see if the backup lights worked, guess what, the shifter won't move, like it is stuck.

Answer:
OK in the process you have blown the brake lamp fuse and this also will affect the shift interlock device. so replace the fuse and see if it blows again or not. if not then great, your back on the road, if so then you have a short to ground somewhere in the circuit.

Car Air Conditioning Repair

Air Conditioning Electrical Diagram

There are several sites on the web that cover details on how the car air conditioning system works. But what most of us want is one web site that can explain the air conditioning system, Tell us how to troubleshoot, how to repair the air conditioning and then how to recharge the A/C. Our Parent site has done all this and more for you Automotive Air Conditioning.

You will discover the troubleshooting procedures you need to determine what is wrong with your air conditioning and how to fix it and recharge it . The procedures are step by step and include diagrams and photos for ease of understanding.

Alternator Repair and Testing

Alternator Repair

Basically this means that an alternator is what charges the car's battery and also provides power to operate the engines computer, lights, radio, etc. So, if the alternator quits functioning then all of these electrical devices will try to run off the car's battery. The problem with that is, once the battery starts to loose power ( since it is no longer being recharged ) the will start to function poorly and will eventually stop running altogether. Generally when the alternator starts to fail a Battery light will illuminate on the dash board. This means the battery is no longer being charged , this does not mean the battery has a problem. Read Entire Article

I am unable to turn the immobiliser off

I have a Hyundai coupe w reg. It has a factory fitted immobiliser. I am unable to turn the immobiliser off, I can open the car with the keys, but when I try the ignition it is dead, nothing works, there are no lights when you open the door, everything is immobilized, how can I turn the immobiliser off so I can use the car, and take it to a garage.

ASNWER:

The immobiliser is integral with the cars ECU, and therefore cannot be switched off, it will need to be diagnosed and either repaired or reprogrammed using a JOBD diagnostic system, that has suitable software. Most good auto electrical engineers should have the correct equipment, and some of them also work mobile, so they may be able to get you up and running without you having to take it to them.

2000 vw beetle has a problem with the battery draining after about three days

2000 VW Beetle

My 2000 VW beetle has a problem with the battery draining after about three days of normal use. Both the battery and alternator check out OK. Also have a problem with driver-side electric windows won't go up or down. Any ideas would be great.

Answer:

More than likely the harness going from the back of the alternator to the battery is faulty. Run the car with the radio, seat heaters, headlights, emergency lights, and rear window defroster on for 20 minutes with the hood closed. Then you need to put a voltmeter with one one lead on the positive battery post and the other on the large wire at the back of the alternator. That measurement should be around .06 volt. If it is over .1 volt the harness is faulty. You can buy one new from the dealer.

Electronic Engine Controls and Sensors | Testing Procedures

All Sequential Fuel Injection (SFI) systems use the EEC system. The heart of the EEC system is a microprocessor called the Powertrain Control Module (PCM). The PCM receives data from a number of sensors and other electronic components (switches, relays, etc.). Based on information received and information programmed in the PCM's memory, it generates output signals to control various relays, solenoids and other actuators. The PCM in the EEC system has calibration modules located inside the assembly that contain calibration specifications for optimizing emissions, fuel economy and driveability. The calibration module is called a PROM.

Electronic Engine Controls and Sensor Testing Procedures
Powertrain Control Module (PCM)
Throttle Position (TP) sensor
Mass Air Flow (MAF) sensor Intake Air Temperature (IAT) sensor
Idle Air Control (IAC) valve
Engine Coolant Temperature (ECT) sensor
Heated Oxygen Sensor (HO2S)
Camshaft Position (CMP) sensor
Knock Sensor (KS)
Vehicle Speed Sensor (VSS)
Crankshaft Position (CKP) sensor

My Electric Power Seats are not working?

Power Seat Wiring Diagram

The power motor that operates the up down motion on the front of the passenger seat is not functioning on my 2000 Silverado. IS this common and what are my options?

Answer:
The seat motors can bind up if run all the way up or down. First check for a blown fuse. It is easy enough to turn the drive with pliers to free it up. If it doesn't turn it is bound. Remove the motor and try to turn it again. If it still doesn't turn then the seat base will need replaced. If it does turn plug the motor in and test it to see if it runs. If the motor does run it may be week from a bad armature or worn brushes. If the motor doesn't run check for power and ground at the motor connector. If it has power and ground the motor is no good. If it doesn't have power and ground The module is probably no good. Verify power and ground at the module before you condemn it.

Defrost only on high and still wont clear up.

2001 LHS. Windows are fogging up in back. Defrost only on high and still wont clear up. Driver only in car and nothing wet inside. Does this model have an air exchange door that I can get at to check if it is stuck?

Answer:

You have it correct, the recirculation door for outside air is stuck closed and not allowing air to come in causing the fogging condition. The motor for this door is on the passenger side of the heater box. I believe that you can see this if you take the glove box out, but it has been a long time since I've worked on one of these for this issue. It is motor number 2. As I looked at the instructions it says the dash has to come out to get to this motor.

96 Monte Carlo with a 3.4 liter motor he keeps burning up his alternator

my friend has a 96 Monte Carlo with a 3.4 liter motor he keeps burning up his alternator,he has replaced it 3 times.the 2nd one was he did not hook up the cowl for it to get air to cool it but it has happened again any ideas or maybe a cure for this would be helpful.





Response:



1) Disconnect that amp and subs.







2) Sounds like something is drawing a lot of amps. Has he been blowing fuses and replaced them with a higher amp fuse? Do any wires feel hot or warm. The fan belt could be over tighten,(this is bad for the bearings). Get it to a garage and have them check it.





3) One of the sensors is bad. Check your voltage at each sensor both cold and hot and compare to specs. Usually high voltage (battery voltage) is a cold cycle circuit. Low voltage (half battery voltage) is the run or warm circuit. This triggers the ECM to set the cycle for ignition and fuel pump. A common problem with the distributor model 4 cyl was the pickup coil and reluctor in what was known as the "Hall Effect" Ignition.

 

4) hall effect is possible. an automatic shut down relay is possible. another strange thing is the map sensor. these are all easy checks to find out no meters or other things. start with the shut down relay which is under the hood in the relay center and switch it with another relay of the same number like the ac or what ever and see if it runs when warm. for the test on the map unplug the vacuum and see if it runs (it will act flooded but it will run) if it is the map and if all else fails it can be the pick-up coil know as the hall effect. in the distributor flat plate their when cap is removed lol and have a great day.

1989 Chevy Truck tail lights go out when I hit the Brakes

I have a 1989 Chevy pick up scottsdale 1500 the left tail light goes out when I activate the brakes any advice would be helpful. thanks



Response:



It's either a bad ground or a bad light socket itself and very common to fail. Your wire harness runs down the drivers side just inside the frame rail to just below the left tail light where it forks and part goes up the other over to the right tail light with quick connectors for the license plate light. UNLESS, someone has installed an aftermarket trailer wiring package. Also check your trailer connection. even though your not using the connection you are still receiving power to the plug. use a test light to make sure it's working properly.



good luck

1999 Chevy Tahoe and I need to replace the Blower Motor Resistor

Blower Motor Resistor = 1

I have a 1999 Chevy Tahoe and I need to replace the Blower Motor Resistor. I understand that it is on top of the blower and access is by removing the radio and heater control panel. Can anyone advise the easiest and best way to safely remove the dash panels to gain access? I don’t want to break anything during the removal process. Thanks!



Response:

The Resistor is under the hood in the engine compartment. It's held onto the fibreglass case with 2 1/4 screws and has 4 wires, 1 going to the blower itself and 3 going into the main harness and back to the switch. So follow that Orange or Tan 10 gauge wire on the blower back to that resistor.

95 Chevy G 20 keeps blowing multiable fuses...

My blinkers were working then I had to do them manually and then they started working again then I smelled smoke and they quit altogether. I also lost my brake lights too at the same time. I changed the bulbs and that didn't work, I took it to muffler man and he said I had multiable fuses blown, but didn't know what had caused it to do that. Muffler man changed the fuses and when I picked up the van, I drove for about 30 minutes and they all blew again. Also I have a small hole in the radiator up at the very top side by the corner, can I use a sealant to fix it or do I have to replace it? it's not leaking enough to even hit the ground, but you can see where it's coming fromby the bubbling it does. So I was hoping maybe someone out there may know something about this problem. Thanks a bunch